Server status
DCS version: 2.5.2.18521
SR version: 1.5.0
As of June 14, 2018
Latest topics
» My Hornet Video
Today at 4:16 by (A/229) BBall

» Grim Reapers' video competition
Today at 2:49 by (B/229) groundhog

» 229th training programme.
Yesterday at 7:08 by (A/229) Grey Rider

» Getting back in the saddle - ideas needed
Yesterday at 1:34 by (A/229) Utley

» uh-1h / sa342
Sat 16 Jun 2018 - 7:37 by (B/229) chippy

» Startup checklist in vr
Sat 16 Jun 2018 - 4:31 by (D/229) Gizzy

» This week for those who fly helicopters.....
Fri 15 Jun 2018 - 16:28 by (D/229) Gizzy

» Got a Little Stick Time Today
Wed 13 Jun 2018 - 21:47 by (A/229) Rob

» Liferaft Rescue help
Wed 13 Jun 2018 - 3:14 by (A/229) Grey Rider

June 2018
MonTueWedThuFriSatSun
    123
45678910
11121314151617
18192021222324
252627282930 

Calendar Calendar

World Clock

Halls effect sensor config assistance

Go down

Halls effect sensor config assistance

Post by (D/229) gadget on Sun 20 May 2018 - 19:07

A general shout out to anyone with experience configuring halls effect sensors, (attempting to repair/re-invent my anti-torque pedals).... Any assistance appreciated
(I'm grounded until I find a solution)
Crying or Very sad
avatar
(D/229) gadget
Warrant Officer 1
Rated Aviator
Warrant Officer 1 Rated Aviator

Messages : 21
Location : Melbourne, Victoria. Australia

http://avimator.net

Back to top Go down

Re: Halls effect sensor config assistance

Post by (D/229) DC on Mon 21 May 2018 - 0:28

Not sure how to answer your question.

I built my collective using the following:

http://www.leobodnar.com/shop/index.php?main_page=product_info&cPath=94&products_id=180

https://www.mouser.com/ProductDetail/Honeywell/HRS100SSAB090/?qs=qefaKJG6iqKQceG1cC5A%2fg%3d%3d

After looking at these let me know if you have any questions.

DC
avatar
(D/229) DC
Chief Warrant Officer 2
Rated Senior Aviator
Chief Warrant Officer 2 Rated Senior Aviator

Messages : 57
Location : Honolulu, HI

Back to top Go down

Re: Halls effect sensor config assistance

Post by (A/229) BlackeyCole on Mon 21 May 2018 - 10:16

Sorry to interrupt but so hall sensors wire up the same as pots?

(A/229) BlackeyCole

Messages : 38
Age : 56
Location : Alamogordo NM

Back to top Go down

Re: Halls effect sensor config assistance

Post by (D/229) DC on Tue 22 May 2018 - 4:40

It certainly depends on the device but usually they do.

Pots consist of a wiper that physically moves along the resistive element, thus can wear out or get "noisy."

Hall effect devices utilize a magnet and and a rotating pickup, thus there is no mechanical contact resulting in a cleaner output signal.

DC
avatar
(D/229) DC
Chief Warrant Officer 2
Rated Senior Aviator
Chief Warrant Officer 2 Rated Senior Aviator

Messages : 57
Location : Honolulu, HI

Back to top Go down

Re: Halls effect sensor config assistance

Post by (A/229) BlackeyCole on Tue 22 May 2018 - 15:11

I was aware of the operation but was aware the magnet was built in I’ll have to look at the ones I purchased recently

(A/229) BlackeyCole

Messages : 38
Age : 56
Location : Alamogordo NM

Back to top Go down

Re: Halls effect sensor config assistance

Post by (D/229) gadget on Wed 23 May 2018 - 1:48

many thanks for the replies
the almighty snark has been assisting me with lots of information and guidance
nudging me in the right direction at least (beating me stupid with a big stick)
cheers
avatar
(D/229) gadget
Warrant Officer 1
Rated Aviator
Warrant Officer 1 Rated Aviator

Messages : 21
Location : Melbourne, Victoria. Australia

http://avimator.net

Back to top Go down

Re: Halls effect sensor config assistance

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top


 
Permissions in this forum:
You cannot reply to topics in this forum